Training and Safety Main Header
Training and Safety

Pilot licenses, training requirements, where to train for your pilot licence, ideas to keep you flying and developing your flying skills, if it goes wrong, find an instructor or examiner to keep you flying.

1) Under CAP 1404, the CAA will contact the Registered owner of the Aircraft to ascertain who the PIC was at the time of the event.

2) The PIC will be asked to complete a Pilot Report, unless the Pilot has already completed a MOR. Following the steps below please copy your response to AOPA as it will provide us with a clear background to the event. You may want to ask AOPA to comment prior to sending to the CAA. 

The Report asks for:

  • The date, time, location, altitude/FL, Infringed Airspace for the event.
  • Crew Experience (Total hours, Hours on type, Last 90 days, Last 28 days, last 24 hours, Licence, Base airfield.)
  • Pilot Recency (Hours in last 12 months, Days since last flight, Days since last flight on type,)
  • Aircraft (Registration, Type, Category (from dropdown list), Typical IAS, ownership type (from dropdown list))
  • Transponder (Equipped, Any comments relevant to use (if relevant))
  • Flight (From, To, Nature of flight (from dropdown list), VFR/IFR, VFR Chart used (from dropdown list), Relevant (planned) route details.)
  • Weather (Visibility, Cloud, Other significant wx.)
  • ATC at time of infringement (ATC Contact (Yes/No)).
  • Use of GPS (GPS Used (Yes/No), Type of GPS, Aircraft equipped with airspace warning device (Yes/No))
  • GA Organisation Membership
  • Description (Brief outline and cause of the incident.)
  • Suggested actions to prevent recurrence.
  • Section 3 – Causal Factors 

It will then be up to the CAA Infringement Co-ordination Group to make an assessment, determine if an infringement occurred and, if so, what was the scale of the infringement and what actions, if any, are appropriate.

infringement categories

AOPA Pilot and Instructor members can get advice and support if they "Ask AOPA" .

Pilot Tips

Suppose you are alerted to traffic at 12 o’clock, five miles, same altitude.

Instinctively, we look to the horizon. However, that’s not quite correct due to the curvature of the earth. Even only 1000 feet in the air, the horizon in the distance is 1.5 degrees below level. By 10,000 feet, that’s about two degrees.

Two degrees is about the width of one finger held out at arm’s length. So if you are flying at 10,000 feet or lower, you need to hold your arm out in front of you at arm’s length and put the bottom of our finger on the horizon. The traffic is somewhere behind that finger, which is a really small slice of the sky just above the horizon. Put the finger down now and look for traffic right there.

Suppose the traffic call was 12 o’clock, five miles, 1000 feet below. Would you look much lower? Not really. A point 1000 feet below you and ten miles away is only one degree down visually. So 1000 feet below and five miles away is two degrees down. If traffic at your altitude is directly behind your finger held at arm’s length, then traffic five miles away and 1000 feet below is just below your outstretched finger. Traffic five miles away and 1000 above, is just above that finger.

In other words, look for traffic two finger-widths above the horizon to one finger width below. That’s where all the traffic is that matters when it’s approaching unless it changes course or altitude.

Get More Pilot Tips from PilotWorkshops Online

Unfortunately, it’s not an unknown IFR error to try a single approach again and again, until impatience, stress or fuel issues result in an accident.

To better manage the risks and temptations of flying multiple instrument approaches, first and foremost you must commit to flying the procedure precisely and by the book. Remember that fatigue, complacency, and temptation to fly just a little lower are constant threats when flying multiple attempts at an approach in low IFR conditions. These threats are what make multiple approaches more dangerous than the first.

As a guide, if you miss an instrument approach, do not attempt the same approach again unless one of these three conditions exists:

1. You have good reason to believe that the weather conditions that required you to miss were temporary and that they’ll improve in time for your second attempt.

2. You can identify a specific technique or part of the procedure you flew incorrectly that caused you to miss, and which you can honestly say you’ll get right the next time. For example, you may not have been completely set up at the final approach fix the first time, and were behind the aircraft for the entire approach. This time you will be certain to be in configuration and on speed before the fix.

3. You’re facing a true emergency and because of equipment failure, unforeseen weather conditions or your own poor planning you have no better options within your remaining range and you must try again before you run out of fuel—a truly dire scenario.

If none of these three conditions apply and you attempt a second approach anyway, you’re just wasting time and the fuel you need to get somewhere else with better conditions or lower approach minimums. More importantly, you’re tempting the human failings that often turn multiple approaches into accident reports.

Get Pilot Tips from PilotWorkshops Online

The Distraction of Glass

If you fly with electronic flight displays, including carry on devices, do you find that you are inclined to spend more time looking inside the aircraft than outside when flying VFR?

We all develop what are called habitual behavior patterns. We have ways of interacting with something, and then we do the same thing in the same situation over and over. So, our habitual behavior pattern when we interact with screens typically involves staring at them for extended periods of time. Think about your work computer or scrolling social media on your phone. When we get into the aircraft, it’s easy to fall into the same pattern and become absorbed with the flight displays and lose situational awareness. That’s true of a glass panel or other tablet or screen. Failure to consistently scan outside of the aircraft is common.

Loss of situational awareness is a common cause of aviation accidents, and fixation on all the information a digital display offers can be just as dangerous as fixation on a minor aircraft problem, a specific instrument, or a distracting passenger.

Habitual behavior patterns aren’t all bad. Think of aircraft pre-flight or preparing for an approach. Repeated actions can build efficiency and reduce errors.

So, minimise your fixation issues by building the right habit patterns. First, be thoroughly familiar with your on board and carry on devices. The more time spent searching for the right button or screen, the less time you have to look outside. Simulators and practice time with a ground power unit are great ways to master on board equipment. For carry on devices you should fully familiarise yourself with the features and operation, including simulatiing a flight if that feature is available, before using it in flight. Be sure your systems and devices are up to date and you can easily locate the features you need.

When you get into the aircraft, build the habit pattern you want. Practice minimal interaction with your screens in flight with conscious breaks between long inputs of data or knob turning to just look outside and fly. Place your carry on device where it is in your line of sight for the windscreen without blocking your view. Finally, resist the temptation to use any personal devices not needed for the flight.

 

Get Pilot Tips from PilotWorkshops Online

 

A go-around during the flare or a rejected landing can be a difficult manoeuvre. Slow airspeed and high power create the greatest number of left-turning tendencies. Further, adding the power causes a pitching up moment which if not corrected can cause the nose to rise quickly and the aircraft could stall. Both of these things need to be corrected promptly. This is why it is so important to include training on these manoeuvres into initial and recurrent training.

First the pitch up. Since the airplane is normally trimmed for the proper approach speed and at low power, when we add full power, the nose will pitch up significantly. We need to be prepared to counter this with forward elevator. If you add the power smoothly while watching the nose in relation to the horizon by looking out at the 10:30 to 11:00 position of the windscreen, you can keep that nose from climbing more than it should. Then you can begin to get the aircraft slowly back in trim. Follow your POH regarding clean up, but be careful not to move flaps or gear until you have good control of the aircraft and then only one thing at a time and re-trim between steps.

Some pilots trim nose up during the flare. Doing this will complicate the out-of-trim condition if a go-around is required.

Now for the left-turning problems. These are at their worst at this time because of the high nose attitude and P-factor (asymmetric blade effect) is at its greatest. So you need to anticipate a need for lots of right rudder as you are adding power. Again you will have to watch out the left side of the engine cowling and keep that cowling aligned with the left side of the runway. Another clue to proper rudder control is to check the ailerons. If you are holding a lot of right aileron, you need more right rudder.

When executing a rejected landing there is no reason to add the power quickly, usually just a little power and a slight pitch up will keep you in the air. So add the power positively but only at a rate that allows you to maintain control of the aircraft.

 

Get Pilot Tips from PilotWorkshops Online

Aircraft generate static electricity just moving through the air; thus the static wicks common on the trailing edges of the flight control surfaces—to give the electricity an easy path off the airplane. When the flying stops, so does the wicking away of static charge. You might even generate a charge as you move about the airplane. Dry air and wool fabric, for example, combined with a little friction, can easily build a small charge. This residual charge could arc to the fuel nozzle as you near the filler port—unless you have properly earthed the aircraft.

But the location of that earth wire matters. Few GA manufacturers specify in the pilot operating handbook where to attach the wire and even fewer GA aircraft have an earthing point for this purpose.

To do its job, the wire must have an electrically conductive path to the fuel port. Corroded surfaces should be avoided for connection because they degrade the electrical path. Similarly, painted surfaces are less conductive than unpainted ones, although in most cases clipping to a portion of the painted landing gear or a painted tiedown ring will not present a significant danger. An unpainted portion of the nosegear structure, an unpainted tiedown ring, or an exhaust stack will usually work well.

The best way to test a location for your airplane using an ohmmeter and a long jumper wire. Clip one end of the wire to your desired location and the other to one of the clips on the ohmmeter. Clip the other connector line from the ohmmeter to the filler neck. The resulting resistance shown on the meter should be less than one ohm. If you’re not familiar with voltmeters/ohmmeters, seek the help of your local maintenance engineer or someone who is familiar with checking resistance measurements.

Remember that even the movement of fuel through the nozzle and into the filler port can generate static electricity. Keep the metal nozzle in contact with the metal ring on the filler port to prevent a spark - BUT make sure that the filler nozzle is not scraped up and down the filler port as it may shave off small pieces of softer metal that fall to the bottom of the fuel tank, where they can cause your fuel test drains to leak

Get More Pilot Tips from PilotWorkshops Online

The instrument scan should be easier with modern glass displays, but for many experienced steam gauge pilots, it’s not.

Consider the altimeter. In level flight, the hundreds needle is usually either straight up or straight down because the altitude you’re holding is either a thousand-foot increment or a thousand plus 500. It’s simple to detect a deviation from needle straight up or needle straight down, even without looking directly at the altimeter. Not so on glass displays, where it seems necessary to look at the altitude tape and process a number.

pilot tips glass panel may24

The solution is using bugs. Set the altitude bug to your target altitude and you’ll see at a glance the relationship between the bug and the altitude pointer. There’s no need to read a number with each scan. That works equally well for any altitude, and for headings and airspeeds too. In many setups, you’ll even get an aural warning when approaching or departing bugged altitudes.

Trend indicators are another helpful feature of glass panels. These are typically magenta lines extending out from the pointers on each performance instrument, that show where you’ll be six seconds in the future if nothing changes. The magenta color stands out even if you’re not looking directly at it. If you’re attempting to maintain altitude, the trend indicator may be your first sign of a deviation, before the altitude itself changes noticeably.

The instrument scan is a crucial IFR skill. For VFR pilots, the more efficient the time spent inside the cockpit is, the more attention can be spent where it belongs: out the window. Practice setting bugs to target values and watching for trend indications, and you’ll soon find that you never want to go back to steam gauges.

Watch this video for more tips about glass cockpits from PilotWorkshops IFR: The Missing Lessons.

Get More Pilot Tips from PilotWorkshops Online

Aircraft Pilot Operating Handbook (POH) Quizzes

Below are links to view three simple open-book POH refresher quizzes for Student Pilots that are designed as ‘pre-test’ quizzes:

AOPA Cessna POH Quiz

AOPA General POH Quiz

AOPA PA28 POH Quiz